COTI – Cisco Optical Technology Intermediate

COTI - Cisco Optical Technology Intermediate

COURSE OUTLINE:

Description

In this course, you will learn how to perform node turn-up. The course covers three shelf types-the M12, M6, and M2. You will learn how to deploy linear and ring dense wavelength-division multiplexing (DWDM) topologies. Additionally, you will learn about multiplexer-demultiplexer cards, Erbium-doped fiber amplifier cards, Raman amplifiers, transponder cards, and the newest Cisco Any Rate muxponder and crossponder cards. These cards are used in terminal, amplifier, and reconfigurable optical add-drop multiplexer (ROADM) node configurations. You will learn how to configure wavelength selective switch (WSS) linear and single-module ROADM (SMR) rings. This course covers 10-GB unprotected circuits and 10-GB protection using Y-cable, optical channel transport unit-2 (OTU-2), and protection switch module (PSM) cards.

Audience

Technical professionals who are responsible for installation, deployment, and maintenance of the Cisco ONS 15454 MSTP network
Network operations, planners, and designers
Network operations engineers

Prerequisites

Basic knowledge of optical transport and protocols
Basic knowledge of data network principles

Learning Objectives

Connect to a Cisco ONS 15454 MSTP chassis using Cisco Transport Controller (CTC)
Node configurations according to card population
Provision DWDM circuits using the CTC
Conduct performance monitoring, alarm verification, and fault isolation
Provision M12 WSS in linear and M6 SMR nodes in ring topologies
Configuration options for the any rate muxponder and crossponder
Perform Raman amplifier initialization
Isolate optical network issues

1. CTC Operations

2. MSTP Topologies

3. Shelf and Card Installation

4. Fiber jumper installation

5. Linear Configurations

6. Node Turn-Up

7. Optical Channel Network Connection Circuits

8. Transponder and Optical Channel Client Connection Circuits

9. Multishelf

10. MSTP M6 SMR-Based Rings

11. 10-Gigabit Muxponder and Transponder Cards

12. 10-Gigabit with Y-Cable Protection

13. Alternative 10-GB Protection (PSM and OTU-2)

14. Any Rate Muxponder and Crossponder

15. Raman Amplifier

16. 40- and 100-Gigabit Transponder and Muxponder

17. Troubleshooting

RELATED COURSES

Technical Training
Cisco

CCIE Wireless Written Bootcamp

Technical Training
Cisco

Cisco IP Contact Center Product Training (IPCCE)

This 5 day Cisco Internet Protocol-Based Contact Center Enterprise (IPCCE) course shows students how to
implement a single site Voice-over-IP Contact Center using Ciscoâ€™s Intelligent Contact Manager (ICM), Call
Manager (CUCM), and IPIVR/Queue Manager (QM). Implementation of a multi-cluster Call Manager
installation is discussed, as well as integration with Legacy ACD environments. Lab exercises include
examples of calls that are initially (post) routed to ICM from both Call Manager and IPIVR. Translation
Routing is discussed and implemented heavily in this class.
Although IPCC Express uses CallManager and IPIVR, this course has nothing to do with IPCC Express
implementations. Configuration of Skilled Agent groups and scripting concepts for IPCC Enterprise are
greatly dissimilar to concepts associated with IPCC Express. Ensure you know which product(s) you are
using before attending this class. IPCC Enterprise has been renamed to UCCE, but the course material is the
exact same.

Technical Training
Cisco

CCNAX v3.0 – CCNA Routing and Switching Boot Camp

The CCNA Routing and Switching Boot Camp is a composite course derived from ICND1 and ICND2 content merged into a single accelerated course. Overlapping content is eliminated and some content is rearranged for the purpose of course flow.

In this course, you will learn how to install, operate, configure, and troubleshoot basic IPv4 and IPv6 networks, including configuring a LAN switch, configuring an IP router, identifying basic security threats, understanding redundant topologies, troubleshooting common network issues, connecting to a WAN, configuring EIGRP and OSPF in both IPv4 and IPv6, understanding wide-area network technologies, and getting familiar with device management and Cisco licensing.

Key additions to this latest revision include an understanding of Quality of Service (QoS) elements and their applicability, how virtualized and cloud services will interact and impact enterprise networks, and an overview of network programmability with the related controller types and tools that are available to support software defined network architectures.

You will learn about the interactions and network functions of firewalls, wireless controllers and access points, along with additional focus on IPv6 and basic network security

A full suite of labs have been developed using the virtual IOS environment with flexible topologies that reinforce concepts with hands-on, guided discovery and challenge labs that align to each lesson module.

This course will enable you to:

Prepare for the CCNA Routing and Switching certification
Operate a medium-sized LAN with multiple switches, supporting VLANs, trunking, and spanning tree
Interactions and network functions of firewalls, wireless controllers and access points
Develop core routing and switching networking skills to configure, monitor, and troubleshoot Cisco networks for increased effectiveness and optimal performance within SMB and Enterprise settings
how device management can be implemented using the traditional and intelligent ways
QoS, virtualization and cloud services, and network programmability related to WAN, access and core segments
Support Cisco network deployments and maintain these services in an on-going operational network.

Course exclusives:

This is an intensive, extended-hours boot camp. Participants should expect to be in class for 12 hours on each of the five days.
To help with your success, you will receive a free CCNA (200-125 CCNAX) voucher.
Lab time:

ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½-120 hours total over 180 days for CCNAX.
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½-Labs are one to one and on Virtual Machines.
ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½ï¿½-Be sure to logout of labs during class. Any remaining lab time can be used after class for additional practice and review.

Technical Training
Cisco

SPEDGE – Implementing Cisco Service Provider Next-Generation Edge Network Services v1.2

In this course, you will learn how to implement Virtual Private Networks (VPNs) within their networks and how to enable service provider point of presence (POP) to provide Layer 2 and Layer 3 VPNs. Through hands-on labs, you will gain practical skills on deploying Cisco IOS/IOS XE and Cisco IOS XR features to operate and support service provider network.

This course helps you prepare for Exam 642-889 SPEDGE, which is needed for CCNP Service Provider certification.